Keurig espresso makers are a preferred method to make a fast and straightforward cup of espresso. Nonetheless, in case your Keurig begins to malfunction, you could must take it aside to troubleshoot the issue. Taking aside a Keurig can appear to be a frightening job, however it’s really fairly easy with the proper instruments and directions.
Earlier than you begin taking aside your Keurig, remember to unplug it from the ability outlet. Additionally, you will want to assemble a couple of instruments, together with a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. Upon getting your instruments, you may observe the steps beneath to take aside your Keurig:
First, take away the water reservoir. The water reservoir is positioned on the again of the Keurig. To take away it, merely carry it up and pull it out. Subsequent, take away the drip tray. The drip tray is positioned beneath the brew head. To take away it, merely pull it out. Lastly, take away the brew head. The brew head is positioned on the prime of the Keurig. To take away it, flip the locking lever to the unlock place and pull the brew head up and out.
Disassembling the Outer Casing
Earlier than you may entry the inside workings of your Keurig, it is advisable to disassemble the outer casing. It is a comparatively easy course of, nevertheless it’s vital to observe the steps rigorously to keep away from damaging your espresso maker.
1. Take away the highest cowl
Begin by eradicating the highest cowl of the Keurig. On most fashions, the highest cowl is held in place by two screws positioned behind the machine. Use a Phillips head screwdriver to take away the screws, then carry the highest cowl off the machine.
As soon as the highest cowl is eliminated, you will notice the water reservoir and the brewing chamber. The water reservoir is positioned on the left facet of the machine, and the brewing chamber is positioned on the proper facet.
To take away the water reservoir, merely carry it up and out of the machine. To take away the brewing chamber, press down on the discharge button positioned on the highest of the chamber, then carry the chamber out of the machine.
2. Take away the facet panels
The subsequent step is to take away the facet panels of the Keurig. On most fashions, the facet panels are held in place by two screws positioned on the prime and backside of every panel. Use a Phillips head screwdriver to take away the screws, then carry the facet panels off the machine.
As soon as the facet panels are eliminated, you will notice the inner elements of the Keurig. These elements embody the heating factor, the pump, and the management board.
3. Take away the underside cowl
The ultimate step is to take away the underside cowl of the Keurig. On most fashions, the underside cowl is held in place by 4 screws positioned on the corners of the quilt. Use a Phillips head screwdriver to take away the screws, then carry the underside cowl off the machine.
As soon as the underside cowl is eliminated, you should have entry to the entire inside elements of the Keurig. Now you can start troubleshooting or repairing your espresso maker.
Eradicating the Water Reservoir
Eradicating the water reservoir is straightforward and may be completed in only a few steps. Be sure that the espresso maker is turned off and unplugged earlier than beginning.
1. Find the water reservoir launch button.
The water reservoir launch button is normally positioned on the again or facet of the espresso maker. It’s sometimes a small, black button.
2. Press the water reservoir launch button and pull the reservoir straight up.
Upon getting positioned the water reservoir launch button, press it and pull the reservoir straight up. The reservoir ought to come out simply. If you’re having bother eradicating the reservoir, strive wiggling it gently back and forth.
The reservoir has quite a lot of inside elements that will dislodge throughout the elimination or filling course of. This is a visible information to assist determine these elements:
| Element | Description |
|---|---|
| Water Stage Indicator | A float that rises and falls with the water degree. |
| Water Stage Sensor | A sensor that detects the water degree and shuts off the espresso maker when the reservoir is empty. |
| Pump | A pump that circulates the water by means of the espresso maker. |
3. As soon as the reservoir has been eliminated, you may clear it with heat, soapy water.
Make certain to rinse the reservoir completely and permit it to dry utterly earlier than changing it.
Disconnecting the Electrical Wires
As soon as you have eliminated the outer casing, it is time to disconnect {the electrical} wires. These wires are what energy the Keurig, so it is vital to watch out when dealing with them.
Step 1: Find the Electrical Wires
{The electrical} wires are positioned on the underside of the Keurig. They’re normally held in place by a plastic clip.
Step 2: Take away the Plastic Clip
Use a screwdriver or your fingernails to take away the plastic clip. This can launch {the electrical} wires.
Step 3: Disconnect the Electrical Wires
As soon as {the electrical} wires are launched, you may disconnect them. To do that, merely pull the wires aside.
| Wire Shade | Connection |
|---|---|
| Black | Frequent |
| Crimson | Line |
| White | Impartial |
Eradicating the Plunger and Needles
To take away the plunger and needles, first take away the highest cowl of the Keurig. Then, find the plunger meeting. It’s a cylindrical-shaped half that’s positioned within the middle of the machine. Grip the plunger meeting and pull it straight up. This can take away the plunger and needles from the machine.
As soon as the plunger and needles have been eliminated, you may clear them. To scrub the plunger, merely wipe it down with a humid material. To scrub the needles, use a delicate brush to take away any espresso grounds or particles. As soon as the plunger and needles are clear, you may reassemble the Keurig.
Cleansing the Plunger Meeting
| Step | Description |
|---|---|
| 1 | Take away the highest cowl of the Keurig. |
| 2 | Find the plunger meeting. It’s a cylindrical-shaped half that’s positioned within the middle of the machine. |
| 3 | Grip the plunger meeting and pull it straight up. This can take away the plunger and needles from the machine. |
| 4 | Wipe down the plunger with a humid material. |
| 5 | Use a delicate brush to take away any espresso grounds or particles from the needles. |
| 6 | Reassemble the Keurig. |
Accessing the Inner Elements
To entry the inner elements of the Keurig machine, you will need to rigorously disassemble the outside housing. This is a step-by-step information to take action:
1. Unplug the Machine
Start by unplugging the Keurig machine from the ability outlet to make sure your security.
2. Find the Screws
Subsequent, find the screws that maintain the outside housing collectively. On most Keurig fashions, these screws are discovered on the again of the machine or beneath the drip tray.
3. Take away the Exterior Housing
Use a screwdriver to take away the screws, after which gently carry the outside housing off the machine. Watch out to not injury any wires or inside elements.
4. Find the Screws Holding the Chassis
Inside the outside housing, you will see that the chassis, which holds the inner elements in place. Find the screws that maintain the chassis in place, that are sometimes discovered on the edges or backside.
5. Take away the Chassis
Use a screwdriver to take away the screws, after which rigorously carry the chassis out of the machine. Take care to not pull any wires or injury any elements.
6. Troubleshooting
Typically throughout disassembly, you could encounter some frequent points. This is a troubleshooting information that will help you resolve them:
| Problem | Answer |
|---|---|
| Stripped screw | Use a rubber band or small piece of paper between the screwdriver and the screw to achieve additional grip. |
| Caught elements | Gently faucet on the element with a rubber mallet or use a skinny, flat software to pry it aside. |
| Broken or disconnected wires | Examine the wires for any injury or disconnection. If needed, reconnect or restore the wires utilizing wire connectors or electrical tape. |
Disconnecting the Management Board
As soon as you have eliminated the highest cowl and entrance panel, it is time to disconnect the management board. It is a delicate step, so take your time and watch out to not injury any of the elements.
Step 1: Determine the Management Board
The management board is normally positioned within the middle of the machine, behind the entrance panel. It is a inexperienced circuit board with plenty of wires and connectors connected to it.
Step 2: Disconnect the Wires
Use a pair of needle-nose pliers to disconnect the wires from the management board. There are two sorts of wires: energy wires and information wires. Energy wires are normally thicker and have a black or purple insulation. Knowledge wires are thinner and have a yellow or white insulation.
Step 3: Take away the Connectors
As soon as the wires are disconnected, you may take away the connectors from the management board. Connectors are small plastic plugs that join the wires to the board. To take away a connector, gently pry it up with a small screwdriver.
Step 4: Raise the Management Board
As soon as the connectors are eliminated, you may carry the management board up and out of the machine. Watch out to not injury any of the elements on the board.
Step 5: Place the Management Board in a Protected Location
As soon as the management board is eliminated, place it in a secure location the place it will not get broken. You possibly can put it in a plastic bag or wrap it in a towel.
Step 6: Double-Examine Your Work
Earlier than you progress on to the following step, double-check your work to make it possible for the entire wires and connectors are disconnected from the management board. This can assist to stop any injury to the machine whenever you reassemble it.
Step 7: Troubleshooting Suggestions
In case you’re having bother disconnecting the management board, listed below are a couple of troubleshooting suggestions:
| Downside | Answer |
|---|---|
| I can not disconnect the wires from the management board. | Just be sure you’re utilizing the proper kind of pliers. Needle-nose pliers are the very best kind of pliers for this job. |
| I can not take away the connectors from the management board. | Strive utilizing a small screwdriver to softly pry the connectors up. Watch out to not injury the connectors or the board. |
| I by chance broken the management board. | In case you by chance broken the management board, you will have to interchange it. You should buy a alternative management board from the producer of your Keurig machine. |
Eradicating the Stream Sensor
The circulate sensor is a small, plastic element positioned within the water line of your Keurig. It helps to find out how a lot water is pumped into the brew chamber. To take away the circulate sensor, observe these steps:
1. Unplug the Keurig
Earlier than you start, make it possible for the Keurig is unplugged from {the electrical} outlet.
2. Find the circulate sensor
The circulate sensor is positioned on the underside of the Keurig, close to the water line.
3. Take away the screws
There are two screws that maintain the circulate sensor in place. Take away these screws utilizing a Phillips head screwdriver.
4. Disconnect the wires
As soon as the screws are eliminated, you will have to disconnect the 2 wires which might be linked to the circulate sensor.
5. Take away the circulate sensor
As soon as the wires are disconnected, you may take away the circulate sensor by gently pulling it out of the water line.
6. Examine the circulate sensor
Upon getting eliminated the circulate sensor, take a second to examine it for any injury. If the circulate sensor is broken, it’ll should be changed.
7. Clear the circulate sensor
If the circulate sensor is just not broken, you may clear it by rinsing it with water.
8. Reinstall the circulate sensor
To reinstall the circulate sensor, merely reverse the steps that you just took to take away it. Make sure to tighten the screws securely, however don’t overtighten them.
Disassembling the Drip Tray
1. **Find the drip tray latch:** The drip tray is held in place by a latch positioned on the underside of the machine.
2. **Press the latch:** Firmly press down on the latch to launch it.
3. **Pull out the drip tray:** As soon as the latch is launched, gently pull out the drip tray.
4. **Take away the cup assist:** The cup assist is a small plastic piece that sits contained in the drip tray. Grasp the cup assist and pull it straight as much as take away it.
5. **Clear the drip tray and cup assist:** Use a humid material to wipe down the drip tray and cup assist. If there’s any espresso residue, use a gentle detergent to wash it off.
6. **Reassemble the drip tray:** Place the cup assist again into the drip tray, then insert the drip tray again into the machine.
7. **Shut the latch:** Push down on the latch to safe the drip tray in place.
Eradicating the Drip Tray Float
8. **Find the drip tray float:** The drip tray float is a small plastic ball that sits contained in the drip tray. It helps to detect when the drip tray is full.
9. **Take away the drip tray float:** To take away the drip tray float, gently push down on the float and pull it out of the drip tray. The float is held in place by a small magnet, so it might require a little bit pressure to take away it.
| Step | Motion |
|---|---|
| 1 | Find the drip tray latch. |
| 2 | Press the latch. |
| 3 | Pull out the drip tray. |
| 4 | Take away the cup assist. |
| 5 | Clear the drip tray and cup assist. |
| 6 | Reassemble the drip tray. |
| 7 | Shut the latch. |
| 8 | Find the drip tray float. |
| 9 | Take away the drip tray float. |
Cleansing and Reassembling the Elements
Now that the Keurig is disassembled, it is time to clear the elements. Use heat, soapy water and a delicate material to wipe down the entire detachable components. Take particular care to wash the needle and the water reservoir.
As soon as the elements are clear, it is time to reassemble the Keurig. Begin by inserting the water reservoir into the bottom of the machine. Then, substitute the drip tray and the Okay-Cup holder.
Subsequent, insert the needle into the highest of the machine. Be sure that the needle is correctly aligned in order that it might puncture the Okay-Cups.
Lastly, substitute the highest of the machine and plug within the Keurig. Your Keurig is now prepared to make use of!
Cleansing the Water Reservoir
The water reservoir is among the most vital elements of your Keurig. It is vital to wash the water reservoir frequently to stop the buildup of mould and micro organism.
To scrub the water reservoir, take away it from the Keurig and rinse it with heat water. Then, add a couple of drops of dish cleaning soap to the water reservoir and swish it round. Lastly, rinse the water reservoir completely with heat water and substitute it within the Keurig.
Cleansing the Needle
The needle is one other vital element of your Keurig. It is vital to wash the needle frequently to stop it from clogging. Some keurig fashions have a detachable needle, whereas others don’t. To scrub the needle, merely use a delicate material and gently wipe away any espresso grounds or different particles. In case your Keurig mannequin has a detachable needle, you may take away it and soak it in heat, soapy water for a couple of minutes. Then, rinse the needle completely with heat water and substitute it within the Keurig.
Cleansing the Okay-Cup Holder
The Okay-Cup holder is one other element of your Keurig that must be cleaned frequently. To scrub the Okay-Cup holder, merely take away it from the Keurig and rinse it with heat water. Then, use a delicate material to wipe away any espresso grounds or different particles. Lastly, substitute the Okay-Cup holder within the Keurig.
| Sort | Cleansing technique |
|---|---|
| Water reservoir | Rinse with heat water, add a couple of drops of dish cleaning soap, swish round, rinse completely |
| Needle | Wipe with a delicate material, take away and soak in heat, soapy water (if detachable) |
| Okay-Cup holder | Rinse with heat water, wipe with a delicate material |
How To Take Aside A Keurig
Listed below are the steps on the right way to take aside a Keurig:
- Unplug the Keurig and let it settle down.
- Take away the water reservoir and drip tray.
- Flip the Keurig the other way up and take away the 4 screws that maintain the underside panel in place.
- Rigorously carry the underside panel off of the Keurig.
- Find the 2 screws that maintain the heating factor in place and take away them.
- Rigorously carry the heating factor out of the Keurig.
- Find the 2 screws that maintain the pump in place and take away them.
- Rigorously carry the pump out of the Keurig.
- Find the 2 screws that maintain the management board in place and take away them.
- Rigorously carry the management board out of the Keurig.
Folks Additionally Ask About How To Take Aside A Keurig
How do I clear the within of my Keurig?
To scrub the within of your Keurig, you will have to descale it. Descaling is the method of eradicating mineral buildup from the within of the Keurig. You possibly can descale your Keurig utilizing a descaling resolution or vinegar.
How do I repair a Keurig that’s not brewing?
In case your Keurig is just not brewing, there are some things you may verify:
- Be sure that the Keurig is plugged in and turned on.
- Be sure that there’s water within the water reservoir.
- Be sure that the Okay-cup is correctly inserted into the Keurig.
- Be sure that the needle within the Keurig is just not clogged.
How do I substitute the water filter in my Keurig?
To exchange the water filter in your Keurig, you will have to:
- Take away the water reservoir from the Keurig.
- Find the water filter within the backside of the water reservoir.
- Take away the previous water filter and insert the brand new water filter.
- Exchange the water reservoir within the Keurig.
