Putting in a wired Ring Doorbell is a comparatively easy course of that may be accomplished in just some minutes. Nonetheless, it is vital to comply with the directions fastidiously to make sure that your doorbell is put in correctly and functioning accurately. On this information, we’ll stroll you thru the step-by-step course of of putting in a wired Ring Doorbell with an present doorbell.
Earlier than you start, you may want to assemble just a few instruments and supplies. You may want a screwdriver, a drill, a degree, and a pair of pliers. You may additionally want the Ring Doorbell, the mounting bracket, and the screws that got here with the doorbell. Moreover, you may have to know the situation of your present doorbell wires.
Upon getting your whole instruments and supplies gathered, you’ll be able to start the set up course of. First, you may have to take away your present doorbell. To do that, merely unscrew the 2 screws which might be holding the doorbell in place. As soon as the screws are eliminated, you’ll be able to pull the doorbell straight off of the wall. Subsequent, you may have to mount the Ring Doorbell mounting bracket. To do that, maintain the mounting bracket as much as the wall the place you wish to set up the doorbell. Use a degree to make it possible for the mounting bracket is degree, after which mark the situation of the screw holes. Upon getting marked the situation of the screw holes, drill two small holes into the wall. Then, insert the screws into the holes and tighten them till the mounting bracket is securely in place.
Selecting the Proper Location
Contemplate visibility and protection: The doorbell ought to present a transparent view of the doorway and canopy the realm you wish to monitor. Keep away from putting it too excessive or low, as this could restrict the sector of view.
Contemplate present wiring: It is ideally suited to decide on a location that already has present doorbell wiring. This may simplify the set up course of and reduce the necessity for extra drilling or electrical work.
Contemplate mounting floor: The doorbell ought to be mounted on a sturdy, flat floor that may assist its weight. Keep away from mounting it on surfaces which might be susceptible to vibrations or motion, as this could have an effect on the doorbell’s efficiency.
Further issues for optimum placement:
| Issue | Suggestion |
|---|---|
| Top | Between 48-54 inches (122-137 cm) from the bottom |
| Angle | Barely downward-facing for optimum area of view |
| Proximity to obstructions | Free from bushes, bushes, or different obstacles that would block the digicam’s view |
| Energy supply | Inside straightforward attain of an present doorbell wire or energy outlet |
Gathering Instruments and Supplies
Needed Instruments
*
Screwdriver (Phillips head and flat head)
*
Drill (with a drill bit appropriate in your wall materials)
*
Wire strippers
*
Electrical tape
*
Stage
Required Supplies
*
Ring Wired Doorbell
*
Mounting bracket
*
Doorbell wiring package
*
Mounting screws
*
Wire nuts
Further Supplies (Non-obligatory)
*
Drill bit for wooden or masonry, relying in your wall materials
*
Caulk or weatherstripping to seal the doorbell base
*
Chime package (if desired)
Putting in the Wiring Package
Earlier than you proceed with the set up, it is essential to substantiate that your present doorbell wiring meets Ring’s compatibility necessities. Here is a desk that will help you confirm:
| Ring Doorbell Compatibility | Current Doorbell Wiring |
|---|---|
| Authentic Ring Doorbell | 8-24VAC, 10VA max, 50/60Hz |
| Ring Doorbell 2 and Ring Doorbell 3 | 8-24VAC, 40VA max, 50/60Hz |
| Ring Doorbell 3 Plus and Ring Doorbell 4 | 16-24VAC, 40VA max, 50/60Hz |
In case your doorbell wiring falls throughout the specified vary, you’ll be able to proceed with the set up. Listed below are the detailed steps for putting in the wiring package:
Step 1: Set up the Mounting Bracket
Determine the rear of the doorbell and find the 2 screw holes on the mounting bracket. Align the mounting bracket vertically and safe it to the wall utilizing the included screws.
Step 2: Join the Wires
Find the present doorbell transformer and establish the terminals labeled “Entrance” and “Trans.” Twist collectively the ends of the doorbell wires that connect with the transformer (“Entrance” wires). Twist collectively the ends of the opposite two doorbell wires that connect with the doorbell button (“Trans” wires). Insert the twisted ends of the “Entrance” wires into the “Entrance” terminal on the doorbell and the twisted ends of the “Trans” wires into the “Trans” terminal.
Step 3: Safe the Wires
To make sure a safe connection, wrap {the electrical} tape across the terminals and wire ends. Don’t overtighten the tape, because it might injury the wires. Use a non-conductive materials, reminiscent of a wire nut or a bit {of electrical} tape, to insulate any uncovered metallic on the wire ends.
Step 4: Join the Pigtail Wires
Find the pigtail wires connected to the doorbell. These wires are sometimes labeled with the letters “FR” and “TR.” Join the “FR” wire to the “Entrance” terminal on the doorbell and the “TR” wire to the “Trans” terminal.
Step 5: Safe the Doorbell
Raise the doorbell onto the mounting bracket and align the 2 screw holes. Tighten the screws to safe the doorbell in place.
Step 6: Take a look at the Doorbell
Press the doorbell button to make sure it’s functioning correctly. If the doorbell chime rings and the Ring app in your smartphone reveals a stay video feed, the set up was profitable.
Mounting the Doorbell Base
Comply with these steps to mount your Ring Doorbell base:
- Flip off energy to the doorbell. Find your doorbell’s circuit breaker or fuse field and switch off the facility to that circuit.
- Take away the present doorbell. Unscrew the screws that maintain the present doorbell in place and disconnect the wires from the again of the doorbell.
- Mount the doorbell base. Use the supplied screws to mount the doorbell base to the wall. Be sure the bottom is degree and safe.
- Join the wires. Join the wires from the doorbell to the terminals on the again of the doorbell base. The terminals are labeled “Entrance” and “Rear”.
- Activate energy to the doorbell. Return to your circuit breaker or fuse field and switch the facility again on to the doorbell circuit.
- Sync your Ring Doorbell. Obtain the Ring app and comply with the directions to sync your doorbell to your smartphone.
Connecting the Doorbell to the Wires
Step 1: Flip Off Energy on the Breaker
Earlier than beginning any electrical work, it is essential to make sure security by turning off the facility to the doorbell circuit on the breaker panel.
Step 2: Take away the Current Doorbell
Find the present doorbell and take away it by unscrewing the mounting screws. Disconnect the wires from the terminals and label them for simple identification.
Step 3: Mount the Ring Doorbell Base
Maintain the Ring Doorbell base towards the wall the place you wish to set up it and mark the screw holes. Use a screwdriver to put in the screws and safe the bottom to the wall.
Step 4: Join the Wires to the Ring Doorbell
Choice 1: Utilizing the Provided Wire Nuts
- Strip about 1/2 inch of insulation from the ends of the doorbell wires.
- Twist the uncovered copper wires collectively from the Ring Doorbell base and the present doorbell wires.
- Safe the connections utilizing the equipped wire nuts and tighten them securely.
Choice 2: Utilizing a Wire Terminal Block (Really helpful)
- Strip about 1/2 inch of insulation from the ends of the doorbell wires.
- Insert the stripped wires into the suitable terminals on the wire terminal block.
- Tighten the terminal screws firmly to safe the connections.
| Wire | Terminal |
|---|---|
| Entrance Doorbell | TB |
| Rear Doorbell (if relevant) | GND |
Step 5: Tuck the Wires and Safe the Ring Doorbell
- Collect all of the wires neatly inside {the electrical} field.
- Push the wires into the junction field and safe them with the supplied wire clamp.
- Place the Ring Doorbell over the baseplate and align the mounting holes.
- Safe the Ring Doorbell to the baseplate by tightening the screws.
Step 6: Flip Energy Again On and Take a look at the Doorbell
- Restore energy to the doorbell circuit on the breaker panel.
- Press the button on the Ring Doorbell to check it.
- If the doorbell rings and the Ring app reveals a stay view, you have got efficiently put in the Ring Doorbell.
Attaching the Doorbell Faceplate
1. Select a Mounting Location: Choose a spot for the doorbell that gives a transparent view of the entryway. Mark the situation with a pencil.
2. Drill Information Holes: Use the supplied drill bit to create two pilot holes on the marked location. The holes ought to be 1 inch aside and degree.
3. Screw within the Mounting Screws: Insert the 2 screws into the pilot holes and tighten them securely utilizing a screwdriver.
4. Connect Alignment Bracket: Take the alignment bracket and slide it over the mounting screws. Be sure the bracket is centered and leveled.
5. Lock the Bracket: Use the supplied safety screw to lock the alignment bracket in place on the mounting screws.
6. Wire the Doorbell: This step varies relying in your present wiring. Seek the advice of the desk beneath for detailed directions:
| Current Wiring | Directions |
|---|---|
| Transformer with doorbell wires | Join the pink wire from the doorbell to the “Entrance” terminal on the doorbell. Join the white wire to the “Again” terminal. |
| Transformer with no doorbell wires | Join the pink wire to the “Entrance” terminal and the white wire to the “Again” terminal. Then, join the black wire to the “Transformer” terminal. |
| Transformerless with doorbell wires | Join the pink wire to the “Entrance” terminal and the white wire to the “Again” terminal on the doorbell. |
| Transformerless with no doorbell wires | Not appropriate with Ring Wired Doorbell. |
7. Safe the Faceplate: Slide the doorbell faceplate over the alignment bracket and press down firmly to snap it into place.
Chiming the Indoor Bell Chime
To chime the indoor bell chime, comply with these steps:
- Press the “Settings” button on the Ring app.
- Choose “Normal Settings.”
- Scroll all the way down to “Doorbell Chime Tones.”
- Choose the chime tone you wish to use.
- Press the “Save” button.
- The chosen chime tone will now play when the doorbell button is pressed.
You may also modify the amount of the indoor bell chime by following these steps:
- Press the “Settings” button on the Ring app.
- Choose “Normal Settings.”
- Scroll all the way down to “Doorbell Chime Quantity.”
- Modify the amount slider to the specified degree.
- Press the “Save” button.
- The quantity of the indoor bell chime will now be adjusted to the chosen degree.
If in case you have a multiple-chime system, you’ll be able to select which chimes to activate. To do that, comply with these steps:
- Press the “Settings” button on the Ring app.
- Choose “Normal Settings.”
- Scroll all the way down to “Chime Connection.”
- Choose the chimes you wish to activate.
- Press the “Save” button.
Verifying the Connection
1. Energy Biking the Ring Doorbell
Maintain down the orange reset button situated on the again of the doorbell for 15 seconds. The doorbell will flip off after which again on, indicating a profitable energy cycle.
2. Checking the Transformer
Make sure that the transformer offering energy to the doorbell is appropriate with Ring’s energy necessities. Examine the specs of your transformer or check with Ring’s web site for appropriate choices.
3. Ringing the Doorbell
Press the doorbell button to check its performance. If the doorbell chimes and prompts, it signifies a profitable connection between the doorbell and transformer.
4. Checking the Wi-Fi Connection
Be sure that your Wi-Fi community is robust and secure. Attempt connecting one other gadget to the Wi-Fi community to confirm its connectivity.
5. Guaranteeing a Sturdy Sign
Place the Ring Doorbell nearer to the Wi-Fi router or use a Wi-Fi extender to spice up the sign energy. The nearer the doorbell is to the router, the higher the sign it’s going to obtain.
6. Checking for Obstructions
Take away any obstructions, reminiscent of metallic objects or thick partitions, that would intervene with the Wi-Fi sign between the doorbell and router.
7. Utilizing the Ring App
Open the Ring app in your smartphone and comply with the directions to attach your doorbell to the app. The app will troubleshoot any connectivity points and supply steerage.
8. Superior Troubleshooting Choices
If the above steps don’t resolve the problem, take into account the next superior troubleshooting choices:
| Troubleshooting Step | Description |
|---|---|
| Resetting the Doorbell and Transformer | Disconnect each the doorbell and transformer for a couple of minutes, then reconnect them to start out contemporary. |
| Utilizing a Completely different Wi-Fi Community | Join the doorbell to a distinct Wi-Fi community to rule out points with the unique community. |
| Inspecting the Wiring | Totally examine the wiring between the doorbell, transformer, and chime field for any injury or free connections. |
| Contacting Ring Help | If all different troubleshooting steps fail, contact Ring’s assist staff for additional help. |
Configuring the Ring Doorbell App
As soon as your Ring Doorbell is put in, you may have to configure the Ring Doorbell app to finish the setup course of. Here is a step-by-step information:
1. Obtain and open the Ring Doorbell app
Obtain the Ring Doorbell app from the App Retailer or Google Play Retailer and open it in your smartphone or pill.
2. Create an account or log in
Should you do not have already got a Ring account, create one by following the on-screen directions. If in case you have an present account, log in utilizing your electronic mail deal with and password.
3. Add a tool
Faucet the “Add System” button on the house display of the app and choose “Doorbells” from the listing of choices.
4. Scan the QR code
Use the digicam in your smartphone or pill to scan the QR code on the again of your Ring Doorbell.
5. Enter your Wi-Fi password
Enter the password in your Wi-Fi community and faucet “Join.”
6. Select a reputation and placement
Give your Ring Doorbell a reputation and choose a location for it within the app.
7. Modify movement detection settings
Customise the movement detection settings to find out when the Ring Doorbell will start recording video. You’ll be able to modify the movement sensitivity, detection zones, and movement schedule.
8. Arrange notifications
Select which notifications you wish to obtain when the Ring Doorbell detects movement or when somebody presses the doorbell button.
9. Superior settings
Discover the superior settings to configure extra options, reminiscent of:
| Setting | Description |
|---|---|
| Two-step verification | Provides an additional layer of safety to your Ring account. |
| Linked accounts | Join your Ring Doorbell to different sensible house gadgets or companies. |
| Subscription plans | Entry extra options and prolonged warranties by subscribing to a Ring Defend plan. |
10. Save and exit
Upon getting configured the settings, faucet “Save” and exit the app. Your Ring Doorbell is now absolutely arrange and able to use.
Troubleshooting Frequent Points
The doorbell will not be powering on
Examine the next:
- Make sure the wire connections are safe and the terminals are tightened.
- The transformer is offering the proper voltage (16-24 VAC).
- Take a look at the transformer with a multimeter to confirm it is working accurately.
- The doorbell will not be shorting out towards any metallic surfaces.
The doorbell will not be connecting to Wi-Fi
Guarantee the next:
- Your Wi-Fi community is functioning correctly.
- The doorbell is inside vary of your Wi-Fi sign.
- The Wi-Fi password entered throughout setup is right.
- The doorbell’s firmware is updated.
- Attempt restarting the doorbell by urgent the reset button for 10 seconds.
The video feed is poor high quality
Study the next:
- Be sure the doorbell’s lens is clear and unobstructed.
- Modify the video settings within the Ring app to optimize high quality.
- Examine the web connection to the doorbell is secure.
- Contemplate putting in a Wi-Fi extender to reinforce sign energy.
- Examine if the doorbell is overheating, as this could have an effect on video high quality.
Doorbell chimes don’t work
Confirm the next:
- The doorbell chime is appropriate with the Ring doorbell.
- The chime is related accurately to the doorbell and energy supply.
- The chime’s quantity is turned up.
- The chime’s batteries are contemporary or the transformer is offering ample energy.
- Examine if the doorbell’s chime settings are configured accurately within the Ring app.
Movement detection not working correctly
Contemplate the next:
- Modify the movement sensitivity settings within the Ring app.
- Be sure the doorbell’s area of view is evident and unobstructed.
- Examine if there are any objects or animals which may be triggering false movement alerts.
- Replace the doorbell’s firmware to make sure it is operating the newest software program.
- Disable some other motion-activated gadgets which may be interfering with the doorbell.
How To Set up Wired Ring Doorbell
Putting in a wired Ring Doorbell is a comparatively easy course of that may be accomplished in just a few hours. Nonetheless, it is very important word that this course of requires some fundamental electrical data and expertise. If you’re not snug working with electrical energy, it’s best to rent a professional electrician to put in your Ring Doorbell for you.
To put in a wired Ring Doorbell, you’ll need the next instruments and supplies:
- A screwdriver
- A drill
- A wire cutter
- A wire stripper
- Electrical tape
- A degree
- A mounting bracket
- Your Ring Doorbell
Upon getting gathered your instruments and supplies, you’ll be able to start the set up course of. Step one is to decide on a location in your Ring Doorbell. The most effective location is often close to your entrance door, the place it’s going to have a transparent view of the realm you wish to monitor. Upon getting chosen a location, use a degree to make sure that the mounting bracket is degree. Mark the situation of the mounting bracket on the wall, after which drill pilot holes for the screws.
Subsequent, join the wires out of your Ring Doorbell to the terminals on the mounting bracket. The pink wire ought to be related to the terminal marked “R”, the black wire ought to be related to the terminal marked “C”, and the yellow wire ought to be related to the terminal marked “V”. As soon as the wires are related, safe the Ring Doorbell to the mounting bracket utilizing the screws supplied.
Lastly, obtain the Ring app in your smartphone and comply with the directions to arrange your Ring Doorbell. As soon as your Ring Doorbell is ready up, you can begin utilizing it to observe your private home and obtain alerts when somebody rings your doorbell.
Folks Additionally Ask
How do I reset my Ring Doorbell?
To reset your Ring Doorbell, press and maintain the setup button for 10 seconds. The Ring Doorbell will then flash white and restart.
How do I modify the batteries in my Ring Doorbell?
To vary the batteries in your Ring Doorbell, take away the faceplate and find the battery compartment. Take away the outdated batteries and insert the brand new batteries. Exchange the faceplate and your Ring Doorbell can be prepared to make use of.
How do I troubleshoot my Ring Doorbell?
If you’re having hassle along with your Ring Doorbell, there are some things you’ll be able to attempt. First, test to make it possible for your Ring Doorbell is related to Wi-Fi. Subsequent, attempt resetting your Ring Doorbell. Lastly, you’ll be able to contact Ring assist for assist.
