Sustaining a clear residence surroundings is important for each your well being and well-being. One essential facet of attaining that is making certain that your Shark Flexstyle vacuum cleaner is working at its greatest. Over time, nonetheless, dust, mud, and particles can accumulate in its filter, hindering its efficiency and probably affecting indoor air high quality. On this article, we’ll present a step-by-step information on the best way to clear the Shark Flexstyle filter successfully, restoring its performance and making certain optimum air purification in your house.
Earlier than embarking on the cleansing course of, it is vital to assemble the required supplies. You will want a vacuum cleaner with a hose attachment, a gentle brush or fabric, and a clear sink or bucket. Moreover, be sure that the vacuum cleaner is unplugged from the facility outlet for security causes. To start, take away the filter from the vacuum cleaner by urgent the discharge button situated on the filter housing. As soon as the filter is indifferent, you may proceed with the cleansing steps outlined beneath.
Firstly, use the vacuum cleaner hose attachment to softly take away any unfastened dust or particles from the filter. It will assist to dislodge any giant particles which will have gathered on the filter floor. Afterward, rinse the filter totally underneath operating water from the sink or bucket. Whereas rinsing, gently agitate the filter to loosen any remaining dust or grime. Keep away from utilizing harsh detergents or chemical compounds, as these might harm the filter materials. As soon as the filter is totally rinsed, shake it vigorously to take away extra water. Lastly, permit the filter to air dry utterly earlier than reinserting it again into the vacuum cleaner. By following these steps, you may successfully clear the Shark Flexstyle filter, making certain optimum efficiency and sustaining a wholesome residence surroundings.
Figuring out the Filter Kind
Shark Flexstyle vacuums are geared up with two kinds of filters: the pre-motor filter and the HEPA filter. The pre-motor filter is situated close to the brushroll, whereas the HEPA filter is situated close to the exhaust port. It is essential to establish the right filter kind to make sure environment friendly cleansing and optimum efficiency of your vacuum cleaner.
Pre-Motor Filter Identification:
The pre-motor filter is usually made of froth and is designed to seize bigger mud particles and particles earlier than they attain the motor. It’s normally situated close to the brushroll, both contained in the dustbin or instantly behind it. To establish the pre-motor filter, check with the vacuum’s person handbook or search for a foam filter part close to the brushroll space. Cleansing the pre-motor filter commonly is important to keep up the vacuum’s suction energy and stop mud buildup inside the motor.
| Pre-Motor Filter Location | Description |
|---|---|
| Contained in the dustbin | Foam filter situated on the backside of the dustbin |
| Behind the brushroll | Foam filter located behind the rotating brushroll |
Eradicating the Filter
The Shark Flexstyle vacuum cleaner has a washable filter that must be cleaned commonly to keep up optimum suction energy. Here is a step-by-step information on the best way to take away the filter:
1. Detach the dust tank from the principle unit by urgent the discharge button and pulling straight up.
2. Open the dust tank by urgent the latch on the underside. The filter is situated on the within of the tank.
3. To take away the filter, press the blue tab on the highest of the filter and pull it straight up. Watch out to not contact the filter materials.
Cleansing the Filter
The filter might be washed with heat water and a gentle detergent. Don’t use bleach or harsh chemical compounds. Rinse the filter totally and permit it to air dry utterly earlier than reattaching it to the dust tank.
Reattaching the Filter
As soon as the filter is dry, reattach it to the dust tank by inserting it into the slot on the within of the tank. Make sure that the filter is absolutely inserted and the blue tab is locked into place.
Reattach the dust tank to the principle unit and also you’re able to vacuum once more.
Here is a abstract of the steps in a desk format:
| Step | Motion |
|---|---|
| 1 | Detach the dust tank. |
| 2 | Open the dust tank. |
| 3 | Take away the filter by urgent the blue tab and pulling it straight up. |
| 4 | Rinse the filter totally with heat water and a gentle detergent. |
| 5 | Permit the filter to air dry utterly. |
| 6 | Reattach the filter to the dust tank. |
| 7 | Reattach the dust tank to the principle unit. |
Cleansing the Filter Foam
Take away the Filter Foam
Find the filter foam on the underside of the vacuum cleaner. Depress the discharge button and pull the filter foam straight as much as take away it.
Rinse the Filter Foam
Use chilly, operating water to rinse the filter foam totally. Keep away from utilizing scorching water, as this may harm the froth.
Squeeze Out Extra Water
Gently squeeze out any extra water from the filter foam. Don’t twist or wring the froth, as this may harm it.
Air Dry the Filter Foam
Place the filter foam in a well-ventilated space to air dry utterly. Keep away from putting the filter foam in direct daylight, as this may trigger it to grow to be brittle.
Notice:
It’s endorsed that you simply clear the filter foam commonly to keep up optimum suction efficiency. The frequency of cleansing will differ relying on how typically you utilize your vacuum cleaner. If you happen to discover a lower in suction energy, it’s a good suggestion to examine the filter foam and clear it if essential.
| Reccommended time for filter substitute |
|---|
| Month-to-month for heavy use |
| Bimonthly for average use |
| Quarterly for mild use |
Cleansing the Felt Filter
The felt filter is situated on the underside of the Shark Flexstyle vacuum cleaner. It’s accountable for capturing high-quality mud and particles from the air. To wash the felt filter, comply with these steps:
-
Unplug the vacuum cleaner from the facility outlet.
-
Take away the mud cup by urgent the discharge button on the highest of the vacuum cleaner.
-
Take away the felt filter from the underside of the mud cup.
-
Rinse the felt filter with chilly water till the water runs clear.
-
**GentlySqueeze Out Extra Water:
After getting rinsed the felt filter, gently squeeze out any extra water.
- Keep away from wringing or twisting the filter, as this may harm the fibers.
- Use a clear towel to soak up any remaining moisture.
- Permit the filter to air-dry utterly earlier than reinserting it into the vacuum cleaner.
-
Reinsert the felt filter into the underside of the mud cup.
-
Reattach the mud cup to the vacuum cleaner.
-
Plug the vacuum cleaner again into the facility outlet and resume use.
Resetting the Filter Indicator
Resetting the filter indicator is a straightforward course of that may be accomplished in only a few steps. Comply with these directions to reset the indicator:
Step 1: Find the Filter Reset Button
The filter reset button is situated on the underside of the Shark Flexstyle vacuum cleaner. It’s a small, black button with a corresponding label. It’s situated close to the dustbin launch button.
Step 2: Press and Maintain the Reset Button
After getting situated the filter reset button, press and maintain it for roughly 5 seconds. The filter indicator mild will start to flash.
Step 3: Launch the Reset Button
As soon as the filter indicator mild has began flashing, launch the reset button. The sunshine will proceed to flash for just a few extra seconds earlier than turning off.
Step 4: Change the Filter
As soon as the filter indicator mild has turned off, you may change the outdated filter with a brand new one. You’ll want to insert the brand new filter appropriately, as indicated within the vacuum cleaner’s person handbook.
Step 5: Test the Filter Indicator
After changing the filter, examine the filter indicator mild to make sure that it has reset. The sunshine must be off, indicating that the filter is clear and able to use.
Step Motion 1 Find the Filter Reset Button 2 Press and Maintain the Reset Button for five Seconds 3 Launch the Reset Button 4 Change the Filter 5 Test the Filter Indicator Clear Shark Flexstyle Filter
The Shark Flexstyle filter is a crucial a part of your vacuum cleaner, and it must be cleaned commonly to maintain your vacuum operating at its greatest. Listed here are the steps on the best way to clear your Shark Flexstyle filter:
- Flip off and unplug the vacuum cleaner.
- Find the filter. The filter is situated within the prime of the vacuum cleaner, behind the dustbin.
- Take away the filter. To take away the filter, press the discharge button on the highest of the vacuum cleaner and pull the filter straight up.
- Clear the filter. You’ll be able to clear the filter by rinsing it with water or by utilizing a vacuum cleaner to take away the mud and dust.
- Permit the filter to dry utterly. Earlier than you set the filter again within the vacuum cleaner, ensure that it’s utterly dry.
- Reinstall the filter. To reinstall the filter, merely push it again into place within the prime of the vacuum cleaner.
- Plug in and activate the vacuum cleaner.
Your Shark Flexstyle filter is now clear and able to use.
Folks Additionally Ask
How typically ought to I clear my Shark Flexstyle filter?
You must clear your Shark Flexstyle filter each 2-3 months, or extra typically in the event you vacuum ceaselessly.
Can I wash my Shark Flexstyle filter within the dishwasher?
No, you shouldn’t wash your Shark Flexstyle filter within the dishwasher. The dishwasher’s warmth and detergent can harm the filter.
The place can I purchase a substitute Shark Flexstyle filter?
You should buy a substitute Shark Flexstyle filter at most main retailers, or on-line.
-
